Back to Blog
How-to Guides 2026-11-14 High Power Model Rocketry 8 views

LOC-IV 4" Build Guide: Fins, Centering Rings, and Fit Checks

LOC-IV 4" Build Guide: Fins, Centering Rings, and Fit Checks

A practical LOC-IV 4" build guide covering fin installation, centering ring alignment, and motor mount fit checks for your Level 1 certification rocket.

Start with the LOC-IV 4" kit's built-in advantages

The LOC-IV 4" arrives with factory pre-slotted airframe tubes and through-the-wall fin construction. That means the fin positions are already defined for you, and the fins extend through the airframe to bond directly to the motor mount. This design reduces alignment guesswork and adds strength where it matters most.

Before you begin, confirm you have the kit components and a clean work area. The LOC-IV is part of the ADVANCED SERIES, rated Intermediate-Advanced complexity, so plan your steps and dry-fit everything before reaching for adhesive.

Kit facts that affect your build sequence

  • LOC-IV 4": Factory pre-slotted airframe and through-the-wall fin construction. The slots set fin alignment, so your fin installation focuses on clean bonding rather than measuring positions.
    LOC-IV 4"
    LOC-IV 4"
  • LOC-IV 4": 38mm motor mount with MR-1 retention and to-the-motor mount construction. The motor mount is the structural backbone for the through-the-wall fins and determines how your motor is retained.
  • LOC-IV 4": Fin thickness: 1/8′′; ring thickness: 1/4′′. These dimensions help you check that fin tabs and centering rings seat correctly in the airframe and motor mount.
  • LOC-IV 4": Shock cord mount: SCM-3 Eyebolt. The recovery anchor is part of the internal assembly, so plan its placement before the motor mount is permanently installed.

Dry-fit the motor mount and centering rings first

A dry run reveals interference before adhesive locks anything in place. Work on a flat, protected surface and keep the airframe tube square.

  1. Slide the centering rings onto the motor mount tube: Check that both 1/4′′ thick rings slide without forcing. If they bind, lightly sand the tube or ring inner edge until they move freely but without slop.
  2. Insert the motor mount into the airframe: The forward ring should sit behind the forward end of the fin slots, and the aft ring should align near the aft end. Confirm the mount is centered in the tube.
  3. Test-fit a fin through its slot: The 1/8′′ fin tab should pass through the airframe slot and contact the motor mount tube. The fin root should sit flush against the airframe with no gap.
  4. Mark alignment before disassembly: Use a pencil to mark the motor mount tube position relative to the airframe so you can repeat the fit during final assembly.

Bond the motor mount with the fins in mind

Once dry-fit is satisfactory, bond the centering rings to the motor mount tube. The forward ring typically sits just ahead of the forward fin slot, and the aft ring near the aft end. Use the marks from your dry-fit to keep the assembly oriented correctly.

Apply adhesive to the fin tabs and the motor mount tube where they meet. Insert the motor mount, then slide each fin through its slot and into contact with the mount. Check that all fins are perpendicular to the airframe and that the trailing edges align. Allow the assembly to cure fully before handling.

Fin installation checkpoints

With the motor mount cured, inspect each fin. The through-the-wall tab should be fully seated against the motor mount, and the fin root should contact the airframe along its full length. Any gap at the root means the fin is not fully inserted; correct it before adding external fillets.

The LOC-IV includes a 36′′ Ripstop Nylon parachute and a 15′ 3/8′′ nylon shock cord with sewn loops. Plan recovery attachment after the fin and motor mount assembly is complete, using the SCM-3 Eyebolt shock cord mount.

Recovery and motor retention details

  • LOC-IV 4": Parachute size: 36′′ Ripstop Nylon. This is the supplied recovery size; confirm it suits your flying field and expected descent rate.
  • LOC-IV 4": Shock cord: NW-15 15′ 3/8′′ Nylon with sewn loops (not elastic). The non-elastic nylon cord requires a proper anchor at the SCM-3 Eyebolt; check the loops and attachment before flight.
  • LOC-IV 4": Motor mount: 38mm with MR-1 Retention. Your motor hardware must match the 38mm mount; the MR-1 retention system secures the motor case.

Motor mount fit and adapter options

The LOC-IV 4" is built around a 38mm motor mount, making it a natural choice for Level 1 certification flights. If you plan to fly smaller F and G motors, the optional MMA-2 motor adapter allows that, but the adapter is not included with the standard kit. Confirm your motor diameter and retention method before heading to the pad.

The kit includes a 23" booster section and an 11" payload section for optional dual deployment setup. The payload section adds flexibility, but the supplied information does not include specific dual-deployment electronics or wiring instructions, so plan that portion separately.

Final fit checks before finishing

Run these checks after the structural assembly has cured and before you commit to paint or decals.

  • Fin alignment: Sight down the airframe from the aft end. All fins should be straight and evenly spaced.
  • Centering ring security: Reach into the aft end and confirm both rings are bonded to the motor mount and airframe with no gaps.
  • Motor mount retention: Test-fit your 38mm motor case or the MMA-2 adapter if using one. The MR-1 retention should hold the motor without play.
  • Shock cord anchor: Check that the SCM-3 Eyebolt is secure and that the nylon shock cord loops are not frayed.
  • Decal planning: The kit includes a logo decal only; a full decal set is available separately if you want more markings.

Related Articles

Customer Service
Home
Products
Cart
Profile