Back to Blog
How-to Guides 2026-11-11 High Power Model Rocketry 10 views

Building the 7.5" Patriot: Motor Mount and Fin Tips

Building the 7.5" Patriot: Motor Mount and Fin Tips

Practical guidance for assembling the 7.5" Patriot high-power rocket kit, focusing on the motor mount and fin installation using supplied components.

What the 7.5" Patriot Kit Includes

The 7.5" Patriot is one of the largest production kits from High Power Model Rocketry, part of the ADVANCED SERIES. It comes with a factory pre-slotted airframe and through-the-wall fin construction, which simplifies alignment and adds strength. The kit includes a 75mm motor mount, an MMA-6 adapter (so you can also fly 54mm motors), 1/4" laser-cut fins, centering rings, and bulkheads.

For recovery, you get a 78" rip-stop nylon parachute, a fire-resistant blanket, a YTN-4 Y harness (attach to 2x SCM-4), tubular nylon, and all necessary hardware. The kit also includes 1500 series rail guides and Z Clip motor retention. Note that this kit is assembled to order, with a lead time of 7-10 business days before shipment, and it ships only within the US and Canada.

Key Components for Your Build

  • 7.5" Patriot: The 7.5" Patriot includes a 75mm motor mount complete with an MMA-6 to give you the ability to fly 54mm motors. This dual-mount capability lets you choose between larger 75mm motors for high thrust or 54mm motors for more conservative flights, giving flexibility without modifying the airframe.
    7.5" Patriot
    7.5" Patriot
  • 7.5" Patriot: The kit features 1/4" laser-cut fins, centering rings, and bulkheads, plus through-the-wall fin construction. Through-the-wall fins provide a stronger bond to the motor mount, reducing the risk of fin failure during high-G flights. The laser-cut parts ensure precise fit with minimal sanding.
  • 7.5" Patriot: Includes a 78" rip-stop nylon parachute, fire-resistant blanket, YTN-4 Y harness, tubular nylon, and all necessary hardware. The large parachute is appropriate for the rocket's weight, and the fire-resistant blanket protects the chute from ejection charge heat. The Y-harness allows dual attachment points for secure deployment.

Motor Mount Assembly Sequence

The motor mount is the structural backbone of the 7.5" Patriot. Follow these steps using the supplied parts.

  1. Prepare the 75mm motor tube: Dry-fit the centering rings onto the 75mm motor tube. The kit includes rings sized for the 7.5" airframe. Mark their positions according to the instruction sheet (YPAT75-2020-Instructions).
  2. Install the MMA-6 adapter: The MMA-6 adapter fits inside the 75mm mount and allows you to fly 54mm motors. Insert it after the centering rings are glued. This adapter is removable, so you can switch motor sizes between flights.
  3. Attach the Z Clip motor retention: The Z Clip system keeps the motor securely in place without screws or tape. Install it on the aft centering ring before gluing the mount into the airframe.
  4. Glue the motor mount assembly: Apply epoxy to the centering rings and slide the assembly into the pre-slotted airframe. Use a long dowel to ensure the mount is centered and aligned with the thrust plate. Let cure fully before proceeding.

Fin Installation with Through-the-Wall Construction

The through-the-wall design means the fin tabs pass through the airframe slots and bond directly to the motor mount. This is stronger than surface-mounted fins.

  1. Dry-fit the fins: Insert each 1/4" laser-cut fin into its pre-cut slot. The tab should reach the motor mount tube. Check for any interference; sand the tab edges lightly if needed for a snug fit.
  2. Apply epoxy to the fin tabs: Use a thickened epoxy (such as Aeropoxy or similar) on the tab and the slot edges. Insert the fin and ensure it is perpendicular to the airframe. Use a square or angle guide to verify alignment.
  3. Add fillets: After the initial bond cures, apply epoxy fillets along the fin root on both sides of the airframe. This adds strength and smooths the transition for better aerodynamics.
  4. Install the rail guides: The kit includes 1500 series rail guides. Attach them to the airframe at the fore and aft positions, aligned with the fins. These allow the rocket to ride on a standard 1515 rail at the launch pad.

What the Catalog Does Not Cover

The supplied evidence does not include specific epoxy curing times, recommended motor delay choices, or painting instructions. For those details, refer to the YPAT75-2020-Instructions sheet included with the kit. The catalog also does not specify the exact length of the 75mm motor tube or the number of centering rings—measure these from the physical parts during dry-fitting. Remember that this kit is assembled to order, so your build may begin with a pre-slotted airframe and pre-cut fins, but the motor mount and fin bonding are still your responsibility.

Related Articles

Customer Service
Home
Products
Cart
Profile