Start with your motor mount, not the airframe
Centering rings for a 1.6" airframe are not one-size-fits-all. The critical dimension is the motor mount tube the ring must accept. The airframe side is fixed by the BT-1.52 (38mm) tube, but the center hole changes with the motor mount: 18mm, 24mm, or 29mm. Before you order, confirm which motor mount your build uses. The ring listing covers all three, so the choice is yours to make deliberately rather than by guesswork.
What the CR-1.52 listing confirms
- Centering Rings For 1.6" Airframe: Centering Rings for BT-1.52 (38mm) to 18mm Motor mount, 1/8′′ thick. 2 Pack includes SCM1 – Kevlar loop. This is the smallest motor mount option in the family, and the 2-pack includes a Kevlar loop for recovery attachment.

Centering Rings For 1.6" Airframe - Centering Rings For 1.6" Airframe: Centering Rings for BT-1.52 (38mm) to 24mm Motor mount, 1/8′′ thick. 2 Pack includes SCM1 – Kevlar loop. The 24mm option uses the same 1/8′′ thickness as the 18mm ring and also includes the Kevlar loop.
- Centering Rings For 1.6" Airframe: Centering Rings for BT-1.52 (38mm) to 29mm Motor mount, 1/4′′ thick. 2 Pack The 29mm ring steps up to 1/4′′ thickness, so it is a different structural choice, not just a different hole size.
- Centering Rings For 1.6" Airframe: Bulkhead BA-152 fits inside of tube coupler TC-1.52 tube coupler to fit 1.63′′ airframe; 1/8′′ wood bulk plate and includes screw eye. The same product family includes a bulkhead for coupler work, useful if your build also needs to close off a tube coupler.
18mm vs 24mm vs 29mm rings at a glance
All three rings fit the same BT-1.52 (38mm) airframe. The differences are the motor mount hole and, for the 29mm version, the ring thickness.
- CR-1.52-18mm: For an 18mm motor mount. 1/8′′ thick. 2-pack includes SCM1 Kevlar loop.
- CR-1.52-24mm: For a 24mm motor mount. 1/8′′ thick. 2-pack includes SCM1 Kevlar loop.
- CR-1.52-29mm: For a 29mm motor mount. 1/4′′ thick. 2-pack.
- Bulkhead BA-152: Not a centering ring. A 1/8′′ wood bulk plate with screw eye, sized for the TC-1.52 tube coupler in a 1.63′′ airframe.
Dry-fit sequence before any glue
The catalog gives you the ring dimensions and contents, not a gluing procedure. Use these checkpoints to confirm the parts fit your actual tubes before you commit to adhesive.
- Confirm the airframe tube: The rings are listed for BT-1.52 (38mm) airframes. Check that your airframe is that tube before anything else.
- Confirm the motor mount tube: Slide the ring over your motor mount tube. The 18mm, 24mm, and 29mm rings are distinct parts, so the hole must match the tube you are using.
- Check ring thickness against your plan: The 18mm and 24mm rings are 1/8′′ thick; the 29mm ring is 1/4′′ thick. Thickness affects how the ring sits in the airframe, so verify it suits your build.
- Account for the Kevlar loop: The 18mm and 24mm 2-packs include an SCM1 Kevlar loop. Decide how it will be routed before the ring is bonded in place.
- Test the bulkhead separately: If you are also using the BA-152 bulkhead, test it in the TC-1.52 tube coupler. It is a coupler part, not an airframe centering ring.
Where the catalog stops and your build takes over
The supplied information does not include a glue type, cure time, or step-by-step bonding sequence for these rings. It also does not state a motor size or performance rating. Treat the listing as a fit and contents reference: it tells you the airframe size, motor mount size, thickness, and pack contents. Your kit instructions or your own scratch-building plan should govern how the rings are bonded and how the Kevlar loop is anchored. If you need those procedural details, confirm them from your kit documentation rather than assuming the ring listing covers them.


