Start with the modular motor can, not the fins
The 2.63 Standard Arm is built around a Modular Motor Can (MMC) that lets you change motor configurations. The kit ships with a 29mm motor tube for E–G motors, and that can is cross-compatible with any other 2.6″ MMC-style kit. Before you reach for glue, decide whether you want to keep that can removable or fix it permanently.
That decision drives the rest of the build. If you want to switch configurations later, the can stays removable using rivets. If you prefer a fixed mount, you glue the can in. Either way, the airframe is pre-slotted, so the fin alignment work starts from a known position rather than a blank tube.
What the kit gives you for mounting and alignment
- 2.63 Standard Arm: Stock with 1 29mm motor tube (E-G) it can easily be switched out for any of the available combinations found here! Confirms the baseline motor mount and that the can is designed to be swapped, which is the first thing to plan before assembly.

2.63 Standard Arm - 2.63 Standard Arm: Using removable rivets you can switch out the configuration at any time! Tells you the removable-can path uses rivets, so you know not to glue the can if you want that flexibility.
- 2.63 Standard Arm: And if you don't want to keep it removable, simply glue the can in for a permanent solution! Gives you the permanent alternative and makes clear that gluing is a deliberate choice, not a default.
- 2.63 Standard Arm: Includes pre-slotted airframe, laser cut fins and rings Pre-slotted tubes and laser-cut parts reduce alignment guesswork, but you still need to dry-fit before adhesive.
A dry-fit sequence before any adhesive
The supplied record confirms the parts and the removable-or-permanent can choice, but it does not give a step-by-step build order. Use this sequence as a fit-check framework, not a substitute for the kit instructions.
- Trial-fit the motor can in the airframe: Slide the 29mm motor can into the 2.6″ airframe and check that it seats without forcing. If you plan to use removable rivets, confirm the rivet holes line up before you commit.
- Set the fins in the pre-slots: Dry-fit each laser-cut fin in its slot. The slots set the position, but check that each fin sits fully down and that the trailing edges line up with one another.
- Test-fit the centering rings: Slide the laser-cut rings onto the motor tube and into the airframe. They should go in without crushing the tube. If they bind, find out why before gluing.
- Check fin alignment by eye and with a straightedge: Sight down the airframe from the rear and compare opposite fins. A straightedge along each fin root will show whether a fin is canted. Correct any misalignment before adhesive sets.
- Decide removable vs permanent can: If you want to switch motor configurations later, keep the can removable with rivets. If you want a fixed mount, glue the can in. The supplied information supports both paths but does not prescribe one.
Alignment checks that matter more than speed
With a pre-slotted airframe and laser-cut fins, the main risk is assuming the slots do all the work. They set the fin station, but they do not guarantee that every fin is square to the tube or that opposite fins are parallel. A few minutes with a straightedge and a rear view will catch a canted fin before glue locks it in.
The same applies to the motor can. If you are keeping it removable, the rivets need to engage cleanly. If you are gluing it, make sure the can is fully seated and aligned with the airframe before adhesive. The kit includes a Kevlar shock cord mount, tubular nylon shock cord, and a fire protection blanket, so plan how those recovery components will sit relative to the can before you close up the airframe.
Recovery and hardware that affect the build layout
- 2.63 Standard Arm: 24′′ rip-stop nylon parachute and swivel, Kevlar shock cord mount, tubular nylon shock cord, fire protection blanket, recovery swivel These parts need space and a sensible attachment point, so account for them while the airframe is still open.
- 2.63 Standard Arm: 1010 rail buttons and 1/4′′ launch lugs Both rail and lug hardware are included, so you can choose your launch setup without sourcing extra parts.
- 2.63 Standard Arm: Vinyl decal set Decals are a finishing step, but knowing they are included helps you plan when to apply them relative to any surface work.
Where the supplied information stops
The kit record confirms the components and the removable-or-permanent can choice, but it does not include a full step-by-step assembly sequence, adhesive recommendations, or torque values for the rivets. Treat the dry-fit sequence above as a way to organize your build, and follow the kit instructions for anything the record does not cover.
The record also does not confirm motor retention hardware beyond the can itself, so check your motor retainer plan separately. If you are new to modular motor cans, the key takeaway is simple: decide removable or permanent first, dry-fit everything, and check fin alignment before any glue goes on.


