Terug naar blog
Handleidingen 2026-11-15 High Power Model Rocketry 11 weergaven

Centreerringen voor 3.00"-rompen: maat- en lijmgids

Centreerringen voor 3.00"-rompen: maat- en lijmgids

Kies de juiste centreerring voor een 3.00 inch romp en motorbevestiging en installeer deze met een lijmplan dat de motorbuis uitgelijnd houdt en de herstelverankering veilig stelt.

Match the ring to the airframe and motor mount first

Centering rings do two jobs: they center the motor mount inside the airframe and they give you a structural surface to bond. On a 3.00" airframe, the ring outside diameter must fit the airframe tube and the inside diameter must fit the motor mount tube you plan to use. The High Power Model Rocketry catalog lists CR-3.00 rings for LOC BT-3.00 airframes in 24 mm, 29 mm, 38 mm, and 54 mm motor mount sizes, plus cluster versions for 4x24 mm, 2x29 mm, and 3x29 mm mounts.

Start by measuring or confirming your airframe and motor mount tube sizes, then choose the ring variant that matches both. The catalog does not list a universal ring, so a 29 mm ring will not center a 38 mm motor tube, and a cluster ring is shaped for multiple motor tubes rather than a single mount.

What the CR-3.00 ring listing confirms

  • Centering Rings for 3.00" Airframe: CR-3.00-24mm: Centering rings for LOC BT-3.00 to 24mm motor mount, 2 pack, 1/8" thick. Use this when your 3.00" airframe carries a single 24 mm motor mount; the 2-pack gives you a forward and aft ring.
    Centering Rings for 3.00" Airframe
    Centering Rings for 3.00" Airframe
  • Centering Rings for 3.00" Airframe: CR-3.00-29mm: Centering rings for BT-3.00 to 29mm motor mount, 2 pack, 1/8" thick, includes screw eye. The 29 mm version is the common mid-power step-up, and the included screw eye gives you a recovery attachment point on the forward ring.
  • Centering Rings for 3.00" Airframe: CR-3.00-38mm: Centering rings for BT-3.00 to 38mm motor mount. Choose this when the build uses a 38 mm motor tube; confirm the ring thickness and pack count on the variant you order because the listing does not repeat them for this size.
  • Centering Rings for 3.00" Airframe: CR-3.00-54mm: Centering rings for BT-3.00 to 54mm motor mount. A 54 mm mount inside a 3.00" airframe leaves little room for error, so dry-fit this ring before any glue goes on.
  • Centering Rings for 3.00" Airframe: Cluster versions: CR-3.00-4x24mm (3 pack, 1/8" thick), CR-3.00-2x29mm (3 pack, 1/8" thick, includes eye bolt), and CR-3.00-3x29mm. Cluster rings are drilled for multiple motor tubes; using a single-mount ring on a cluster build will not align the tubes.

Dry-fit before you choose a glue

Slide the rings onto the motor mount tube and into the airframe before mixing any adhesive. The ring should sit flat against the tube without forcing, and the motor tube should pass through the inside diameter without wobble. If the ring binds on the motor tube, stop and confirm you have the right variant rather than sanding away material that keeps the mount centered.

The catalog lists 1/8" thickness for the 24 mm, 29 mm, and cluster rings and 1/4" thickness for the 38 mm variant. Thicker rings give more bonding surface but take up more internal length, so check that the forward ring will not interfere with the recovery anchor or the intended motor tube length.

The listing notes that the forward ring is notched so you can add a harness or shock cord to the motor tube. That notch is a placement cue: orient it where the recovery harness will run, and confirm the notch lines up before the epoxy cures.

A supported glue sequence for 3.00" centering rings

  1. Confirm the variant and count the rings: Match the ring to the airframe and motor mount, then check the pack count. The 24 mm and 29 mm rings ship as 2 packs; the 4x24 mm and 2x29 mm cluster rings ship as 3 packs. The 38 mm and 54 mm listings do not state a pack count in the supplied text, so verify before you plan the build.
  2. Test-fit the forward ring and orient the notch: Slide the forward ring onto the motor tube and position the notch where the shock cord or harness will attach. The catalog states the forward ring is notched for a harness or shock cord; it does not specify a notch orientation, so choose one that keeps the cord clear of the motor tube.
  3. Bond the forward ring to the motor tube: Apply adhesive around the motor tube where the forward ring sits, then slide the ring into place. The supplied information does not name a specific adhesive or cure time, so follow the adhesive manufacturer's instructions and keep the ring square to the tube while it sets.
  4. Install the aft ring after the forward ring is set: Once the forward ring is secure, slide the aft ring onto the motor tube and test-fit the assembly in the airframe. Bond the aft ring to the motor tube, then bond both rings to the airframe once alignment is confirmed.
  5. Attach the recovery anchor: The 29 mm ring includes a screw eye and the 2x29 mm cluster ring includes an eye bolt. Install the supplied hardware in the forward ring per the hardware's own instructions; the catalog does not specify a torque or thread-locking method.

Where the glue actually needs to go

A centering ring has two bond lines: the inside diameter to the motor tube and the outside diameter to the airframe. The inside bond keeps the motor tube centered; the outside bond transfers thrust and landing loads into the airframe. On a high power rocket motor mount, both bonds matter, and the forward ring also carries the recovery anchor.

The catalog does not specify an adhesive type, fillet size, or cure schedule for these rings. Rather than guessing, use the adhesive system you already trust for the airframe material and follow its published instructions. Keep adhesive out of the motor tube interior and out of the notch where the harness runs.

If you are building a cluster mount, the same logic applies to each motor tube. The cluster rings are drilled for multiple tubes, so bond each tube to the ring before bonding the ring to the airframe.

Checkpoints before the epoxy sets

  • Motor tube is centered: Look through the airframe from both ends; the motor tube should sit concentric with the airframe, not offset toward one side.
  • Rings sit flat: Each ring should contact the motor tube around its full circumference with no visible gap on one side.
  • Notch and hardware are accessible: The forward ring notch and the screw eye or eye bolt should be reachable for harness attachment after the assembly is bonded in.
  • No adhesive in the motor bore: Wipe any squeeze-out from the inside of the motor tube before it cures; a cured blob can prevent the motor from seating.

What the catalog does not confirm

The supplied listing does not state a recommended adhesive, bond strength, cure time, or motor thrust rating for any CR-3.00 variant. It also does not confirm pack counts or thickness for the 38 mm and 54 mm rings, or whether the 3x29 mm cluster ring includes hardware. Treat those as open questions to verify with the product listing or the manufacturer before you rely on them for a build decision.

For a 3.00" airframe build, the safe approach is to choose the ring by motor mount size, dry-fit everything, and follow your adhesive's instructions rather than a generic recipe. That keeps the centering ring sizing decision grounded in the catalog and the installation grounded in the materials you actually have.

Gerelateerde artikelen

Customer Service
Home
Producten
Winkelwagen
Profiel