블로그로 돌아가기
사용 방법 가이드 2026-11-20 High Power Model Rocketry 0 조회수

EZI-65 Rocket Kit: Specs, Build & Flight Tips

EZI-65 Rocket Kit: Specs, Build & Flight Tips

Get the key specs and practical build advice for the EZI-65 high power rocket kit, including motor options and assembly checkpoints.

What the EZI-65 Kit Includes

The EZI-65 is a lightweight high power rocket from the ISP Performance Series. It features a factory pre-slotted airframe and through-the-wall fin construction, which simplifies alignment and strengthens the fin-to-body bond. The kit includes a 54mm motor mount with MR-1 retention, a 36″ ripstop nylon parachute, and a 15′ 3/8″ nylon shock cord with sewn loops. The shock cord mounts to an SCM-3 eyebolt, and the fin stock is 1/8″ thick with 1/4″ ring thickness. The kit is designed for parachute recovery and comes with downloadable instructions and a RockSim file.

Key Specifications at a Glance

  • EZI-65: Height: 57.75″, Diameter: 4″, Weight: 3.2 lbs, Motor Mount: 54mm, Parachute: 36″ Ripstop Nylon. These dimensions tell you the rocket’s size and weight, which affects field requirements and recovery system sizing.
    EZI-65
    EZI-65
  • EZI-65: The 54mm motor mount is great for Level 1 motors. Designed for the Aerotech I-65 motor, it also flies on the Aerotech J-90 for a Level 2 attempt. This kit can serve both Level 1 and Level 2 certification flights, making it a versatile choice for advancing rocketeers.
  • EZI-65: Optional motor mount adapters (MMA-3 for 29mm, MMA-4 for 38mm) allow use of G, H, and I motors. If you already have smaller motors or want to fly on lower impulse, these adapters give you flexibility without buying a new airframe.

Build Checkpoints for the EZI-65

The catalog confirms pre-slotted airframe and through-the-wall fin construction. Use these checkpoints during assembly to avoid common mistakes.

  1. Dry-fit the fins and motor mount: Before applying adhesive, slide the motor mount into the airframe and test-fit the fins through the slots. Check that the fin tabs seat fully into the slots and that the motor mount sits flush against the forward centering ring.
  2. Align the fin slots with the motor mount: Because the airframe is pre-slotted, the fin tabs must align with the motor mount’s centering rings. Rotate the motor mount until the slots line up. Mark the position lightly with a pencil.
  3. Use the supplied shock cord mount: The SCM-3 eyebolt is the designated attachment point. Install it before closing the airframe. The 15′ nylon shock cord with sewn loops attaches directly to the eyebolt.
  4. Check the parachute fit: The 36″ ripstop nylon parachute should pack loosely into the 4″ body tube. If it fits too tightly, consider a smaller chute or a longer shock cord to reduce deployment stress.

Motor Selection and Flight Planning

The EZI-65 was designed around the Aerotech I-65 motor, but its 54mm mount accommodates a range of high power motors. For Level 1 certification, an I-class motor like the I-65 is a natural fit. If your field allows, the J-90 motor gives a Level 2 attempt with a noticeably higher flight. The optional MMA-3 and MMA-4 adapters let you fly G, H, and I motors in 29mm or 38mm casings, which is useful for smaller fields or when you want to conserve propellant cost. Always verify the motor’s total impulse against your launch site dimensions and local regulations.

관련 게시글

Customer Service
홈
상품
장바구니
내 정보